S4R Rebuild

Two Ducs

Active member
Almost completed the rebuild of my 996 S4R. I’ve been trying to crank the motor over on the button to get some oil circulating. I’ve left the fuel pump and coil sticks disconnected but when I turn the key all I get is the oil warning light illuminated, no neutral light and nothing else works. I’ve checked all fuses and shorted the neutral switch to earth, still nothing. The immobiliser light flashes with the ignition off and in the on position. In the end I cranked the motor by putting a direct 12v on the starter motor which achieved what I wanted to do. Does the fuel pump need to be connected in order to get the permissive to turn the motor over on the button? Can’t understand why there’s no neutral light? If I disconnect the dash multi connector plug and plug it in again the clocks do a full sweep and the right front indicator flashes along with the rear left!!! It then reverts to just the oil warning light illuminated. It is of course possible I have the indicator wiring crossed. The whole loom has been off during the refurb

Ian
 
Sidestand safety switch relay is often a problem if you have one, try linking it out to see if the dash lughts come on - or you could plug in the fuel pump to see if it spins - it won't if the relay is lazy
 
Cheers, will give it a go. Was a bit reluctant to run the fuel pump dry but I’ll see what happens. Looks like I had the indicators crossed so now the RH indicators flash quickly when I plug in the dash! Bit odd?
 
Hi Chris, yes I saw that, missed it initially and thought I’d found the problem but it made no difference when I connected it. Seems to be something that’s holding off supplies to several circuits including voltage to the neutral switch
 
Chris, I’ve got the small black lead connected to the negative post on the battery??
 

Attachments

  • IMG_2350.webp
    IMG_2350.webp
    80.2 KB · Views: 274
Underside of it is clean but I’ll take it off and have another go. Just wondering if it’s in the right place though?
 
Have you fiddled with the two relays to the rhs of the battery box? Most people upsize them from 20-30 amp and they can give connectivity probs. You can also just swap them over to see if the symptoms remain the same?
 
Thanks all for the advice. I’ve connected the fly lead to the ECU heat sink and now the bike is completely dead apart from the flashing immobiliser light! Anyone know how to bypass the immobiliser? I’ll also try and bypass the side stand switch next! Think the next step will be to find out where I’ve got 12v downstream of the ignition switch
 
Have you fiddled with the two relays to the rhs of the battery box? Most people upsize them from 20-30 amp and they can give connectivity probs. You can also just swap them over to see if the symptoms remain the same?
I’m guessing you mean the two relays to the left of the battery cradle? I can’t see any others. I’ll try swapping them
 
Is the light constan or flashing and if flashing, is it doing a series of flashing then pausing to flash the same amount over and over?
 
Yes, sorry, lhs…
Just swapped the relays and the dash lit up like a Christmas tree 😀. The outermost relay has failed. Still won’t start on the button but Ive only one relay fitted. Not sure which one does what, I’ll consult the wiring diagram. Thanks Laava and all the others for your suggestions 👍
 

Attachments

  • IMG_2351.webp
    IMG_2351.webp
    122.3 KB · Views: 265
  • IMG_2353.webp
    IMG_2353.webp
    50.7 KB · Views: 305
Just swapped the relays and the dash lit up like a Christmas tree 😀. The outermost relay has failed. Still won’t start on the button but Ive only one relay fitted. Not sure which one does what, I’ll consult the wiring diagram. Thanks Laava and all the others for your suggestions 👍
I think one is the head lights. Try the lights...
 
Back
Top Bottom