Help required - why 3 spigots?

West Cork Paul

Man in a Shed
Subscriber
Can anyone with knowledge of a very early production Monster 900 tell me why there are 3 spigots underneath the tank?

It’s a ‘94 reg bike but its frame number is 499. Judging by the handwritten name and date on the underside of the tank (sorry no photo of that at present) I’m assuming it’s the original tank.

IMG_3849.webp


The 2 spigots with the braided pipe on are the breather and overflow/water drain. In the top right is the fuel level sensor and the stop cock/fuel delivery connector is out of shot on the right.

The reason I ask is the spigot which is not attached to anything appeared to be blocked off, however, it’s now started leaking fuel so clearly comes straight from the tank.

My questions are;

Should that spigot be blocked off?
Why is it there if that’s the case?
What’s the best solution to fix the leak? Just block it up with JB weld? Or something better eg live with the leak but run another pipe to the fuel filter via a T connection in the existing pipe between the tank and fuel filter so the leaking fuel just goes into the fuel filter and feeds the carbs.
 
Can anyone with knowledge of a very early production Monster 900 tell me why there are 3 spigots underneath the tank?

It’s a ‘94 reg bike but its frame number is 499. Judging by the handwritten name and date on the underside of the tank (sorry no photo of that at present) I’m assuming it’s the original tank.

View attachment 93111

The 2 spigots with the braided pipe on are the breather and overflow/water drain. In the top right is the fuel level sensor and the stop cock/fuel delivery connector is out of shot on the right.

The reason I ask is the spigot which is not attached to anything appeared to be blocked off, however, it’s now started leaking fuel so clearly comes straight from the tank.

My questions are;

Should that spigot be blocked off?
Why is it there if that’s the case?
What’s the best solution to fix the leak? Just block it up with JB weld? Or something better eg live with the leak but run another pipe to the fuel filter via a T connection in the existing pipe between the tank and fuel filter so the leaking fuel just goes into the fuel filter and feeds the carbs.
Don’t know but could it be a breather pipe and the internal pipe has rotted out / come loose
 
I’ve been through every parts diagram from 93 to 98, none of them show 2 pipes ie breather and overflow, none show the underneath of the tank and most only have the one breather pipe. Flow & return was mentioned and later models do have that but remember this is not a fuel i jection model so there’s no pressurised system there. Sure there’s a vacuum operated pump but that’s relatively low pressure and to make sure at WOT the flow to the carb’s float bowls can keep up.

I’m veering to blocking it up with JB but I know the best long term and permanent solution is to put a T piece into the pipe from the fuel cock to the fuel filter and then run a fuel pipe from that spigot to the T piece.
 
I’ve been through every parts diagram from 93 to 98, none of them show 2 pipes ie breather and overflow, none show the underneath of the tank and most only have the one breather pipe. Flow & return was mentioned and later models do have that but remember this is not a fuel i jection model so there’s no pressurised system there. Sure there’s a vacuum operated pump but that’s relatively low pressure and to make sure at WOT the flow to the carb’s float bowls can keep up.

I’m veering to blocking it up with JB but I know the best long term and permanent solution is to put a T piece into the pipe from the fuel cock to the fuel filter and then run a fuel pipe from that spigot to the T piece.
If it was ok with it blocked i would seal it off and be done with it, if later down the road it needs to be unblocked then so be it. Do you have any blanking grommets, thinking that further down the road if it needs clearing JB WELD will need drilling out.

1702156242333.webp
 
I’ve been through every parts diagram from 93 to 98, none of them show 2 pipes ie breather and overflow, none show the underneath of the tank and most only have the one breather pipe. Flow & return was mentioned and later models do have that but remember this is not a fuel i jection model so there’s no pressurised system there. Sure there’s a vacuum operated pump but that’s relatively low pressure and to make sure at WOT the flow to the carb’s float bowls can keep up.

I’m veering to blocking it up with JB but I know the best long term and permanent solution is to put a T piece into the pipe from the fuel cock to the fuel filter and then run a fuel pipe from that spigot to the T piece.

Maybe a generic tank for a FI model? Or a later tank put on this bike?
 
Don’t know but could it be a breather pipe and the internal pipe has rotted out / come loose
If that were the case it would be impossible to replace, just from myself design pov that doesn’t make sense so I don’t think it is.
Maybe a generic tank for a FI model? Or a later tank put on this bike?
Possibly. 🤔
@West Cork Paul Can you tell me if this excerpt from a 1993 M900 Workshop Manual is the area of interest?

View attachment 93120
That’s it, and now I have my answer. Thank you @Everclear 🙏👍.

I have a workshop manual for the 93 model but it doesn’t have that diagram in it. From that diagram I can see that that is the fuel supply spigot and where the fuel cock is on this tank is not where it should be. The parts diagrams show a bolt, no.27 in @Markduc ‘s link above, which is the drain plug for the tank.

So, it seems someone has blanked off the original fuel supply spigot, whatever they used (JB Weld?) is now leaking, they then removed the drain plug and replaced it with a fuel cock.

Well, that’s that sorted. Thank you 🙏🙏

Now, do I just blank it off or do a better, more permanent fix? Or, remove the fuel cock, replace it with the drain plug and reinstate the original fuel supply point - that would be the best (but most time consuming and costly) fix.
 
As the drain pipe will have a shorter internal spigot it will allow dross and water from the bottom of the tank to go to the carb/injector
Therefore it would be better to reinstate the original supply spigot.
Very good point. Mind you the inside of the tank was in very good condition when I shoved the camera in there, but see my comment below.
Yep, but original nozzle may be corroded so would need integrity checking first 😏
I suspect the original nozzle/spigot got partially blocked somehow and the flow of fuel was drastically reduced. Rather than drain the tank, rinse it out with water and wait for it to dry before drilling out the spigot, I suspect they just tapped into the drain plug hole and blocked off the original fuel supply with something like JB; certainly there’s grey JB looking stuff up there.
I’m going to explain it to the owner and he can sort it, I’m deffo not drilling into the tank unless it’s been dry of fuel and fully vented for a good few weeks.
This is the fuel system from a 93 monster
Nowhere does it show a return pipe very confusing, I would have the filler cap off and a nosey inside the tank
View attachment 93156
Why would it need a return pipe. The float bowl will shut off supply once the floats full and the pump is very low pressure, a vacuum operated diaphragm, that’s there to make sure the float bowl can remain replenshied at WOT - no?
 
Very good point. Mind you the inside of the tank was in very good condition when I shoved the camera in there, but see my comment below.

I suspect the original nozzle/spigot got partially blocked somehow and the flow of fuel was drastically reduced. Rather than drain the tank, rinse it out with water and wait for it to dry before drilling out the spigot, I suspect they just tapped into the drain plug hole and blocked off the original fuel supply with something like JB; certainly there’s grey JB looking stuff up there.
I’m going to explain it to the owner and he can sort it, I’m deffo not drilling into the tank unless it’s been dry of fuel and fully vented for a good few weeks.

Why would it need a return pipe. The float bowl will shut off supply once the floats full and the pump is very low pressure, a vacuum operated diaphragm, that’s there to make sure the float bowl can remain replenshied at WOT - no?
It wouldn’t but Your tank looks like it has 2 fuel pipes + a breather overflow outlet
where do the 2 large fuel pipes go
it just seems odd
 
I’ve been through every parts diagram from 93 to 98, none of them show 2 pipes ie breather and overflow, none show the underneath of the tank and most only have the one breather pipe. Flow & return was mentioned and later models do have that but remember this is not a fuel i jection model so there’s no pressurised system there. Sure there’s a vacuum operated pump but that’s relatively low pressure and to make sure at WOT the flow to the carb’s float bowls can keep up.

I’m veering to blocking it up with JB but I know the best long term and permanent solution is to put a T piece into the pipe from the fuel cock to the fuel filter and then run a fuel pipe from that spigot to the T piece.
Can you call Italy and ask the question ?
 
It wouldn’t but Your tank looks like it has 2 fuel pipes + a breather overflow outlet
where do the 2 large fuel pipes go
it just seems odd
The 2 braided pipes that go straight down are connected to the drain and breather spigots, they exit between the swing arm and rear of engine.

The larger black fuel pipe in this photo has been put in place temporarily by me so I could have the end of it above the fuel tank and stop the leak from filling my workshop with explosive fumes.

IMG_3856.webp
 
Now why would I need to that when everything that’s unknown and all one could ever want to know, including all the known unknowns and all the unknown unknowns can be found amongst, and answered by, all the members here 😉.
Any unknowns always sound much tastier when explained by a beautiful Italian young lady Paul, , so let us know yes🤷🏻‍♂️😎😆
 
Now why would I need to that when everything that’s unknown and all one could ever want to know, including all the known unknowns and all the unknown unknowns can be found amongst, and answered by, all the members here 😉.

Especially me.

That’s it, and now I have my answer. Thank you @Everclear 🙏👍.

I have a workshop manual for the 93 model but it doesn’t have that diagram in it. From that diagram I can see that that is the fuel supply spigot and where the fuel cock is on this tank is not where it should be.

So, it seems someone has blanked off the original fuel supply spigot, whatever they used (JB Weld?) is now leaking, they then removed the drain plug and replaced it with a fuel cock.

Well, that’s that sorted. Thank you 🙏🙏
 
Back
Top Bottom